Frequent Links
Consolidation (soil)
This article includes a list of references, related reading or external links, but its sources remain unclear because it lacks inline citations. (October 2014) 
Consolidation is a process by which soils decrease in volume. According to Karl von Terzaghi "consolidation is any process which involves a decrease in water content of saturated soil without replacement of water by air." In general it is the process in which reduction in volume takes place by expulsion of water under long term static loads. It occurs when stress is applied to a soil that causes the soil particles to pack together more tightly, therefore reducing its bulk volume. When this occurs in a soil that is saturated with water, water will be squeezed out of the soil. The magnitude of consolidation can be predicted by many different methods. In the Classical Method, developed by Terzaghi, soils are tested with an oedometer test to determine their compression index. This can be used to predict the amount of consolidation.
When stress is removed from a consolidated soil, the soil will rebound, regaining some of the volume it had lost in the consolidation process. If the stress is reapplied, the soil will consolidate again along a recompression curve, defined by the recompression index. The soil which had its load removed is considered to be overconsolidated. This is the case for soils which have previously had glaciers on them. The highest stress that it has been subjected to is termed the preconsolidation stress. The over consolidation ratio or OCR is defined as the highest stress experienced divided by the current stress. A soil which is currently experiencing its highest stress is said to be normally consolidated and to have an OCR of one. A soil could be considered underconsolidated immediately after a new load is applied but before the excess pore water pressure has had time to dissipate.
Contents
Consolidation analysis
Spring analogy
The process of consolidation is often explained with an idealized system composed of a spring, a container with a hole in its cover, and water. In this system, the spring represents the compressibility or the structure of the soil itself, and the water which fills the container represents the pore water in the soil.
 The container is completely filled with water, and the hole is closed. (Fully saturated soil)
 A load is applied onto the cover, while the hole is still unopened. At this stage, only the water resists the applied load. (Development of excess pore water pressure)
 As soon as the hole is opened, water starts to drain out through the hole and the spring shortens. (Drainage of excess pore water pressure)
 After some time, the drainage of water no longer occurs. Now, the spring alone resists the applied load. (Full dissipation of excess pore water pressure. End of consolidation)
Primary consolidation
This method assumes consolidation occurs in only onedimension. Laboratory data is used to construct a plot of strain or void ratio versus effective stress where the effective stress axis is on a logarithmic scale. The plot's slope is the compression index or recompression index. The equation for consolidation settlement of a normally consolidated soil can then be determined to be:
<math> \delta_c = \frac{ C_c }{ 1 + e_0 } H \log \left( \frac{ \sigma_{zf}' }{ \sigma_{z0}' } \right) \ </math>
where
 δ_{c} is the settlement due to consolidation.
 C_{c} is the compression index.
 e_{0} is the initial void ratio.
 H is the height of the soil.
 σ_{zf} is the final vertical stress.
 σ_{z0} is the initial vertical stress.
C_{c} can be replaced by C_{r} (the recompression index) for use in overconsolidated soils where the final effective stress is less than the preconsolidation stress. When the final effective stress is greater than the preconsolidation stress, the two equations must be used in combination to model both the recompression portion and the virgin compression portion of the consolidation processes, as follows,
<math> \delta_c = \frac{ C_r }{ 1 + e_0 } H \log \left( \frac{ \sigma_{zc}' }{ \sigma_{z0}' } \right) + \frac{ C_c }{ 1 + e_0 } H \log \left( \frac{ \sigma_{zf}' }{ \sigma_{zc}' } \right)\ </math>
where σ_{zc} is the preconsolidation stress of the soil.
Secondary compression
Secondary compression is the compression of soil that takes place after primary consolidation. Even after the reduction of hydrostatic pressure some compression of soil takes place at slow rate. This is known as secondary compression.Secondary compression is caused by creep, viscous behavior of the claywater system, compression of organic matter, and other processes. In sand, settlement caused by secondary compression is negligible, but in peat, it is very significant. Due to secondary compression some of the highly viscous water between the points of contact is forced out.
Secondary compression is given by the formula
<math>S_s=\frac{H_0}{1+e_0} C_{a} \log \left( \frac {t} {t_{90} } \right) \ </math>
Where H_{0} is the height of the consolidating medium
e_{0} is the initial void ratio
C_{a} is the secondary compression index
t is the length of time after consolidation considered
t_{90} is the length of time for achieving 90% consolidation
Time dependency
The time for consolidation to occur can be predicted. Sometimes consolidation can take years. This is especially true in saturated clays because their hydraulic conductivity is extremely low, and this causes the water to take an exceptionally long time to drain out of the soil. While drainage is occurring, the pore water pressure is greater than normal because it is carrying part of the applied stress (as opposed to the soil particles).
See also
External links
23px  This section is empty. You can help by adding to it. (December 2012) 
References
 Coduto, Donald (2001), Foundation Design, PrenticeHall, ISBN 0135897068
 Kim, Myungmo (2000), Soil Mechanics (in 한국어) (4 ed.), Seoul: Munundang, ISBN 8973930532
 Terzaghi, Karl (1943), Theoretical soil mechanics, John Wiley&Sons, Inc., p. 265
