Open Access Articles- Top Results for Genoa %28sail%29

Genoa (sail)

File:SC70 RETRO Photo D Ramey Logan.jpg
SC70 RETRO's genoa overlaps the main sail and the mast

The genoa or genny was originally referred to as an 'overlapping jib' and later as a Genoa jib. It is a type of large jib or staysail that overlaps the main sail, sometimes eliminating it. It is used on single-masted sloops and twin-masted boats such as yawls and ketches. Its larger surface area increases the speed of the craft in light to moderate winds; in high wind conditions a smaller jib is usually substituted, and downwind a spinnaker may be used. The feature that distinguishes a genoa from a working jib is that the former extends past the mast, overlapping the mainsail when viewed from the side.[1]


File:Jib vs genoa.svg
A jib, left, compared to a roughly 110% genoa, right. The foretriangle is outlined in red.

The term Jib is the generic term for any of an assortment of headsails. The term genoa (or genny) refers to a type of jib that is larger than the 100% foretriangle, which is the triangular area formed by the point at which the stay intersects the mast, and deck or bowsprit, and the line where the mast intersects deck at the rail. Colloquially the term is sometimes used interchangeably with jib. A working jib is no larger than the 100% foretriangle. A genoa is larger, with the leech going past the mast and overlapping the mainsail. To maximize sail area, the foot of the sail is generally parallel and very close to the deck when close hauled.

Genoas are categorized by a percentage representing their area relative to the 100% foretriangle. Sail racing classes often specify a limit to genoa size. Genoas are classified by their size; a modern number 1 genoa would typically be approximately 155%, but historically number 1 genoas have been as large as 180%. Number 2 genoas are generally in the range of 125%-140%. Working jibs are also defined by the same measure, typically 100% or less of the foretriangle. Under Performance Handicap Racing Fleet rules, most boats are allowed 155% genoas without a penalty.[2]

Handling issues

Maximizing the sail area can cause more difficult handling. It may be harder to tack a genoa than a jib, since the overlapping area can become tangled with the shrouds and/or mast unless carefully tended during the tack. Genoas are very popular in some racing classes, since they count only the foretriangle area when calculating foresail size; a genoa allows a significant increase in actual sail area within the calculated sail area. In boats where sail restrictions are not applicable, genoas of 180% overlap can be found, although those over 150% are not often seen, since the additional area is shadowed by the mainsail when close hauled and generates diminishing returns in terms of power per actual sail area.

The gennaker

The gennaker has been around for several decades now, and as the name suggests, it is a hybrid between a genoa and an asymmetrical spinnaker. A brand name of North Sails, the gennaker started as a cruising sail based on the Code 0 spinnakers used on racing boats. Gennakers and similar code 0 variants offered by other makers are even larger than genoas (200% overlaps are not uncommon), and they have a much greater camber for generating larger amounts of lift when reaching. Flat-cut gennakers can be effective for angles as low as 60–70 degrees. Spinnakers perform much better when running because the main sail blocks the wind of gennaker above 135–150 degrees.


The famous Swedish sailor and shipowner Sven Salén (1890–1969) first used the genoa on his 6 m R-yacht "May-Be" by the 1926 in Coppa di Terreno in Genua, hence the name. He successfully used it during the Scandinavian Gold Cup's races of 1927 in Oyster Bay (US). Sven Salén also pioneerd the parachute spinnacre.

A similar type of jib was in use for centuries by the fishermen in the Netherlands with their Botter type ships. The fishermen relied on the combination of a large jib while fishing so the mainsail could remain unused. After fishing the fisherman's jib[3] helped to get the fish to markets fast.

A correct explanation of the interaction between jib and mainsail was published by aerodynamicist and yachtsman Arvel Gentry in 1981,[4] and "is much more complicated than the old theories imply". This states that the widely believed explanation of the slot effect is "completely wrong" and shows that this is not due to the venturi effect (or "valve effect" to use Curry's term) accelerating the air in the slot. Instead it is shown that the air in the slot is slowed down and its pressure increased reducing the tendency of the mainsail to stall, that the mainsail reduces the air pressure on the lee side of the jib accelerating that airflow, and that the mainsail increases the angle at which the air meets the luff of the jib, allowing the boat to point higher. Gentry points out that proper understanding of sail interaction allows better sail trimming.


  1. ^ Jerry Cardwell, Dieter Loibner (2007). Sailing Big on a Small Sailboat, 3rd. Ed. Sheridan House, Inc. p. 68. ISBN 1-57409-247-2. 
  2. ^ Ross Garrett (1996). The symmetry of sailing. Sheridan House, Inc. p. 124. ISBN 1-57409-000-3. 
  3. ^ nl:Botter
  4. ^ A Review of Modern Sail Theory, Proceedings of the Eleventh AIAA Symposium on the Aero/Hydronautics of Sailing September 12, 1981