Inertial navigation system
|This article includes a list of references, but its sources remain unclear because it has insufficient inline citations. (June 2009)|
An inertial navigation system (INS) is a navigation aid that uses a computer, motion sensors (accelerometers) and rotation sensors (gyroscopes) to continuously calculate via dead reckoning the position, orientation, and velocity (direction and speed of movement) of a moving object without the need for external references. It is used on vehicles such as ships, aircraft, submarines, guided missiles, and spacecraft. Other terms used to refer to inertial navigation systems or closely related devices include inertial guidance system, inertial reference platform, inertial instrument, inertial measurement units (IMU) and many other variations.
- 1 Overview
- 2 Error
- 3 History
- 4 Guidance in human spaceflight
- 5 Aircraft inertial guidance
- 6 Inertial navigation systems in detail
- 7 Basic schemes
- 7.1 Gimballed gyrostabilized platforms
- 7.2 Fluid-suspended gyrostabilized platforms
- 7.3 Strapdown systems
- 7.4 Motion-based alignment
- 7.5 Vibrating gyros
- 7.6 Hemispherical resonator gyros (wine glass or mushroom gyros)
- 7.7 Quartz rate sensors
- 7.8 MHD sensor
- 7.9 MEMS gyroscope
- 7.10 Ring Laser Gyros (RLG)
- 7.11 Fiber optic gyros (FOG)
- 7.12 Pendular accelerometers
- 7.13 TIMU (Timing & Inertial Measurement Unit) sensors
- 8 Method
- 9 See also
- 10 References
- 11 External links
Inertial navigation is a self-contained navigation technique in which measurements provided by accelerometers and gyroscopes are used to track the position and orientation of an object relative to a known starting point, orientation and velocity. Inertial measurement units (IMUs) typically contain three orthogonal rate-gyroscopes and three orthogonal accelerometers, measuring angular velocity and linear acceleration respectively. By processing signals from these devices it is possible to track the position and orientation of a device.
Inertial navigation is used in a wide range of applications including the navigation of aircraft, tactical and strategic missiles, spacecraft, submarines and ships. Recent advances in the construction of microelectromechanical systems (MEMS) have made it possible to manufacture small and light inertial navigation systems. These advances have widened the range of possible applications to include areas such as human and animal motion capture.
An inertial navigation system includes at least a computer and a platform or module containing accelerometers, gyroscopes, or other motion-sensing devices. The INS is initially provided with its position and velocity from another source (a human operator, a GPS satellite receiver, etc.), and thereafter computes its own updated position and velocity by integrating information received from the motion sensors. The advantage of an INS is that it requires no external references in order to determine its position, orientation, or velocity once it has been initialized.
An INS can detect a change in its geographic position (a move east or north, for example), a change in its velocity (speed and direction of movement), and a change in its orientation (rotation about an axis). It does this by measuring the linear acceleration and angular velocity applied to the system. Since it requires no external reference (after initialization), it is immune to jamming and deception.
Inertial-navigation systems are used in many different moving objects, including vehicles—such as aircraft, submarines, spacecraft—and guided missiles. However, their cost and complexity place constraints on the environments in which they are practical for use.
Gyroscopes measure the angular velocity of the system in the inertial reference frame. By using the original orientation of the system in the inertial reference frame as the initial condition and integrating the angular velocity, the system's current orientation is known at all times. This can be thought of as the ability of a blindfolded passenger in a car to feel the car turn left and right or tilt up and down as the car ascends or descends hills. Based on this information alone, the passenger knows what direction the car is facing but not how fast or slow it is moving, or whether it is sliding sideways.
Accelerometers measure the linear acceleration of the system in the inertial reference frame, but in directions that can only be measured relative to the moving system (since the accelerometers are fixed to the system and rotate with the system, but are not aware of their own orientation). This can be thought of as the ability of a blindfolded passenger in a car to feel themselves pressed back into their seat as the vehicle accelerates forward or pulled forward as it slows down; and feel themselves pressed down into their seat as the vehicle accelerates up a hill or rise up out of their seat as the car passes over the crest of a hill and begins to descend. Based on this information alone, they know how the vehicle is accelerating relative to itself, that is, whether it is accelerating forward, backward, left, right, up (toward the car's ceiling), or down (toward the car's floor) measured relative to the car, but not the direction relative to the Earth, since they did not know what direction the car was facing relative to the Earth when they felt the accelerations.
However, by tracking both the current angular velocity of the system and the current linear acceleration of the system measured relative to the moving system, it is possible to determine the linear acceleration of the system in the inertial reference frame. Performing integration on the inertial accelerations (using the original velocity as the initial conditions) using the correct kinematic equations yields the inertial velocities of the system, and integration again (using the original position as the initial condition) yields the inertial position. In our example, if the blindfolded passenger knew how the car was pointed and what its velocity was before he was blindfolded, and if they are able to keep track of both how the car has turned and how it has accelerated and decelerated since, they can accurately know the current orientation, position, and velocity of the car at any time.
All inertial navigation systems suffer from integration drift: small errors in the measurement of acceleration and angular velocity are integrated into progressively larger errors in velocity, which are compounded into still greater errors in position. Since the new position is calculated from the previous calculated position and the measured acceleration and angular velocity, these errors accumulate roughly proportionally to the time since the initial position was input. Therefore the position must be periodically corrected by input from some other type of navigation system. The inaccuracy of a good-quality navigational system is normally less than 0.6 nautical miles per hour in position and on the order of tenths of a degree per hour in orientation. If navigation systems malfunction, they can send planes off course.
Accordingly, inertial navigation is usually used to supplement other navigation systems, providing a higher degree of accuracy than is possible with the use of any single system. For example, if, in terrestrial use, the inertially tracked velocity is intermittently updated to zero by stopping, the position will remain precise for a much longer time, a so-called zero velocity update. In aerospace particularly, other measurement systems are used to determine INS inaccuracies, e.g. the Honeywell LaseRefV inertial navigation systems uses GPS and Air data computer outputs to maintain Required navigation performance. The navigation error rises with the lower price (and sensitivity) of the sensors used. Currently, devices combining different sensors are being developed, e.g. Attitude and heading reference system. Because the navigation error is mainly influenced by the numerical integration of angular rates and accelerations, new measurement systems which use absolute measurement types are being developed, such as the Pressure Reference System.
Estimation theory in general, and Kalman filtering in particular, provide a theoretical framework for combining information from various sensors. One of the most common alternative sensors is a satellite navigation radio, such as GPS which can be used for all kinds of vehicles with direct sky visibility. Indoor applications can use pedometers, distance measurement equipment, or other kinds of Position sensors. By properly combining the information from an INS and other systems (GPS/INS), the errors in position and velocity are stable. Furthermore, INS can be used as a short-term fallback while GPS signals are unavailable, for example when a vehicle passes through a tunnel.
|The examples and perspective in this section deal primarily with the United States and do not represent a worldwide view of the subject. (January 2015)|
Inertial navigation systems were originally developed for rockets. American rocket pioneer Robert Goddard experimented with rudimentary gyroscopic systems. Dr. Goddard's systems were of great interest to contemporary German pioneers including Wernher von Braun. The systems entered more widespread use with the advent of spacecraft, guided missiles, and commercial airliners.
Early German World War II V2 guidance systems combined two gyroscopes and a lateral accelerometer with a simple analog computer to adjust the azimuth for the rocket in flight. Analog computer signals were used to drive four graphite rudders in the rocket exhaust for flight control. The GN&C (Guidance, Navigation, and Control) system for V2 provided many innovations as an integrated platform with closed loop guidance. At the end of the war Von Braun engineered the surrender of 500 of his top rocket scientists, along with plans and test vehicles, to the Americans. They arrived at Fort Bliss, Texas in 1945 under the provisions of Operation Paperclip and were subsequently moved to Huntsville, Alabama, in 1950  where they worked for U.S. Army rocket research programs.
In the early 1950s, the US government wanted to insulate itself against over dependency on the German team for military applications, including the development of a fully domestic missile guidance program. The MIT Instrumentation Laboratory (later to become the Charles Stark Draper Laboratory, Inc.) was chosen by the Air Force Western Development Division to provide a self-contained guidance system backup to Convair in San Diego for the new Atlas intercontinental ballistic missile  (Construction and testing were completed by Arma Division of AmBosch Arma). The technical monitor for the MIT task was a young engineer named Jim Fletcher who later served as the NASA Administrator. The Atlas guidance system was to be a combination of an on-board autonomous system, and a ground-based tracking and command system. The self-contained system finally prevailed in ballistic missile applications for obvious reasons. In space exploration, a mixture of the two remains.
In the summer of 1952, Dr. Richard Battin and Dr. J. Halcombe "Hal" Laning, Jr., researched computational based solutions to guidance, and undertook the initial analytical work on the Atlas inertial guidance in 1954. Other key figures at Convair were Charlie Bossart, the Chief Engineer, and Walter Schweidetzky, head of the guidance group. Schweidetzky had worked with Wernher von Braun at Peenemuende during World War II.
The initial Delta guidance system assessed the difference in position from a reference trajectory. A velocity to be gained (VGO) calculation is made to correct the current trajectory with the objective of driving VGO to zero. The mathematics of this approach were fundamentally valid, but dropped because of the challenges in accurate inertial guidance and analog computing power. The challenges faced by the Delta efforts were overcome by the Q system (see Q-guidance) of guidance. The Q system's revolution was to bind the challenges of missile guidance (and associated equations of motion) in the matrix Q. The Q matrix represents the partial derivatives of the velocity with respect to the position vector. A key feature of this approach allowed for the components of the vector cross product (v, xdv, /dt) to be used as the basic autopilot rate signals—a technique that became known as cross-product steering. The Q-system was presented at the first Technical Symposium on Ballistic Missiles held at the Ramo-Wooldridge Corporation in Los Angeles on June 21 and 22, 1956. The Q system was classified information through the 1960s. Derivations of this guidance are used for today's missiles.
Guidance in human spaceflight
In Feb of 1961 NASA awarded MIT a contract for preliminary design study of a guidance and navigation system for Apollo. MIT and the Delco Electronics Div. of General Motors Corp. were awarded the joint contract for design and production of the Apollo Guidance and Navigation systems for the Command Module and the Lunar Module. Delco produced the IMUs (Inertial Measurement Units) for these systems, Kollsman Instrument Corp. produced the Optical Systems, and the Apollo Guidance Computer was built by Raytheon under subcontract. (see Apollo on-board guidance, navigation, and control system, Dave Hoag, International Space Hall of Fame Dedication Conference in Alamogordo, N.M., October 1976 ).
For the space shuttle, an open loop (no feedback) guidance was used to guide the shuttle from lift off until Solid Rocket Booster (SRB) separation. After SRB separation the primary space shuttle guidance is named PEG (Powered Explicit Guidance). PEG takes into account both the Q system and the predictor-corrector attributes of the original "Delta" System (PEG Guidance). Although many updates to the shuttle's navigation system have taken place over the last 30 years (ex. GPS in the OI-22 build), the guidance core of the Shuttle GN&C system has evolved little. Within a manned system, there is a human interface needed for the guidance system. As Astronauts are the customer for the system, many new teams are formed that touch GN&C as it is a primary interface to "fly" the vehicle.
Aircraft inertial guidance
One example of a popular INS for commercial aircraft was the Delco Carousel, which provided partial automation of navigation in the days before complete flight management systems became commonplace. The Carousel allowed pilots to enter a series of waypoints, and then guided the aircraft from one waypoint to the next using an INS to determine aircraft position and velocity. Boeing Corporation subcontracted the Delco Electronics Div. of General Motors to design and build the first production Carousel systems for the early models (-100, -200, and -300) models of the 747 aircraft. The 747 utilized three Carousel systems operating in concert for reliability purposes. The Carousel system and derivatives thereof were subsequently adopted for use in many other commercial and military aircraft. The USAF C-141 was the first military aircraft to utilize the Carousel in a dual system configuration, followed by the C-5A which utilized the triple INS configuration, similar to the 747. The KC-135 fleet was fitted with a dual Carousel system that was aided by a Doppler radar.
INSs contain Inertial Measurement Units (IMUs) which have angular and linear accelerometers (for changes in position); some IMUs include a gyroscopic element (for maintaining an absolute angular reference).
Angular accelerometers measure how the vehicle is rotating in space. Generally, there is at least one sensor for each of the three axes: pitch (nose up and down), yaw (nose left and right) and roll (clockwise or counter-clockwise from the cockpit).
Linear accelerometers measure non-gravitational accelerations of the vehicle. Since it can move in three axes (up & down, left & right, forward & back), there is a linear accelerometer for each axis.
A computer continually calculates the vehicle's current position. First, for each of the six degrees of freedom (x,y,z and θx, θy and θz), it integrates over time the sensed acceleration, together with an estimate of gravity, to calculate the current velocity. Then it integrates the velocity to calculate the current position.
Inertial guidance systems are now usually combined with satellite navigation systems through a digital filtering system. The inertial system provides short term data, while the satellite system corrects accumulated errors of the inertial system.
An inertial guidance system that will operate near the surface of the earth must incorporate Schuler tuning so that its platform will continue pointing towards the center of the earth as a vehicle moves from place to place.
Gimballed gyrostabilized platforms
Some systems place the linear accelerometers on a gimbaled gyrostabilized platform. The gimbals are a set of three rings, each with a pair of bearings initially at right angles. They let the platform twist about any rotational axis (or, rather, they let the platform keep the same orientation while the vehicle rotates around it). There are two gyroscopes (usually) on the platform.
Two gyroscopes are used to cancel gyroscopic precession, the tendency of a gyroscope to twist at right angles to an input force. By mounting a pair of gyroscopes (of the same rotational inertia and spinning at the same speed in opposite directions) at right angles the precessions are cancelled, and the platform will resist twisting.
This system allows a vehicle's roll, pitch, and yaw angles to be measured directly at the bearings of the gimbals. Relatively simple electronic circuits can be used to add up the linear accelerations, because the directions of the linear accelerometers do not change.
The big disadvantage of this scheme is that it uses many expensive precision mechanical parts. It also has moving parts that can wear out or jam, and is vulnerable to gimbal lock. The primary guidance system of the Apollo spacecraft used a three-axis gyrostabilized platform, feeding data to the Apollo Guidance Computer. Maneuvers had to be carefully planned to avoid gimbal lock.
Fluid-suspended gyrostabilized platforms
Gimbal lock constrains maneuvering, and it would be beneficial to eliminate the slip rings and bearings of the gimbals. Therefore, some systems use fluid bearings or a flotation chamber to mount a gyrostabilized platform. These systems can have very high precisions (e.g., Advanced Inertial Reference Sphere). Like all gyrostabilized platforms, this system runs well with relatively slow, low-power computers.
The fluid bearings are pads with holes through which pressurized inert gas (such as Helium) or oil press against the spherical shell of the platform. The fluid bearings are very slippery, and the spherical platform can turn freely. There are usually four bearing pads, mounted in a tetrahedral arrangement to support the platform.
In premium systems, the angular sensors are usually specialized transformer coils made in a strip on a flexible printed circuit board. Several coil strips are mounted on great circles around the spherical shell of the gyrostabilized platform. Electronics outside the platform uses similar strip-shaped transformers to read the varying magnetic fields produced by the transformers wrapped around the spherical platform. Whenever a magnetic field changes shape, or moves, it will cut the wires of the coils on the external transformer strips. The cutting generates an electric current in the external strip-shaped coils, and electronics can measure that current to derive angles.
Cheap systems sometimes use bar codes to sense orientations, and use solar cells or a single transformer to power the platform. Some small missiles have powered the platform with light from a window or optic fibers to the motor. A research topic is to suspend the platform with pressure from exhaust gases. Data is returned to the outside world via the transformers, or sometimes LEDs communicating with external photodiodes.
Lightweight digital computers permit the system to eliminate the gimbals, creating strapdown systems, so called because their sensors are simply strapped to the vehicle. This reduces the cost, eliminates gimbal lock, removes the need for some calibrations, and increases the reliability by eliminating some of the moving parts. Angular rate sensors called rate gyros measure how the angular velocity of the vehicle changes.
A strapdown system has a dynamic measurement range several hundred times that required by a gimbaled system. That is, it must integrate the vehicle's attitude changes in pitch, roll and yaw, as well as gross movements. Gimballed systems could usually do well with update rates of 50–60 Hz. However, strapdown systems normally update about 2000 Hz. The higher rate is needed to keep the maximum angular measurement within a practical range for real rate gyros: about 4 milliradians. Most rate gyros are now laser interferometers.
The data updating algorithms (direction cosines or quaternions) involved are too complex to be accurately performed except by digital electronics. However, digital computers are now so inexpensive and fast that rate gyro systems can now be practically used and mass-produced. The Apollo lunar module used a strapdown system in its backup Abort Guidance System (AGS).
Strapdown systems are nowadays commonly used in commercial and tactical applications (aircraft, ships, ROV's missiles, etc.) and are starting to become more widespread in applications where superb accuracy is required (like submarine navigation or strategic ICBM guidance) and FOG based strapdown inertial navigation systems have been selected by the UK Royal Navy for the Astute class submarine and the Queen Elizabeth class aircraft carriers.
The orientation of a gyroscope system can sometimes also be inferred simply from its position history (e.g., GPS). This is, in particular, the case with planes and cars, where the velocity vector usually implies the orientation of the vehicle body.
For example, Honeywell's Align in Motion is an initialization process where the initialization occurs while the aircraft is moving, in the air or on the ground. This is accomplished using GPS and an inertial reasonableness test, thereby allowing commercial data integrity requirements to be met. This process has been FAA certified to recover pure INS performance equivalent to stationary align procedures for civilian flight times up to 18 hours. It avoids the need for gyroscope batteries on aircraft.
Less-expensive navigation systems, intended for use in automobiles, may use a vibrating structure gyroscope to detect changes in heading, and the odometer pickup to measure distance covered along the vehicle's track. This type of system is much less accurate than a higher-end INS, but it is adequate for the typical automobile application where GPS is the primary navigation system, and dead reckoning is only needed to fill gaps in GPS coverage when buildings or terrain block the satellite signals.
Hemispherical resonator gyros (wine glass or mushroom gyros)
If a standing wave is induced in a hemispheric resonant cavity, and then the resonant cavity is rotated, the spherical harmonic standing wave rotates through an angle different from the quartz resonator structure due to the Coriolis force. The movement of the outer case with respect to the standing wave pattern is proportional to the total rotation angle and can be sensed by appropriate electronics. The system resonators are machined from quartz due to its excellent mechanical properties. The electrodes that drive and sense the standing waves are deposited directly onto separate quartz structures that surround the resonator. These gyros can operate in either a whole angle mode (which gives them nearly unlimited rate capability) or a force rebalance mode that holds the standing wave in a fixed orientation with respect to the gyro housing (which gives them much better accuracy).
This system has almost no moving parts, and is very accurate. However it is still relatively expensive due to the cost of the precision ground and polished hollow quartz hemispheres. Northrop Grumman currently manufactures IMUs (inertial measurement units) for spacecraft that use HRGs. These IMUs have demonstrated extremely high reliability since their initial use in 1996.
Quartz rate sensors
This system is usually integrated on a silicon chip. It has two mass-balanced quartz tuning forks, arranged "handle-to-handle" so forces cancel. Aluminum electrodes evaporated onto the forks and the underlying chip both drive and sense the motion. The system is both manufacturable and inexpensive. Since quartz is dimensionally stable, the system can be accurate.
As the forks are twisted about the axis of the handle, the vibration of the tines tends to continue in the same plane of motion. This motion has to be resisted by electrostatic forces from the electrodes under the tines. By measuring the difference in capacitance between the two tines of a fork, the system can determine the rate of angular motion.
These products include 'tuning fork gyros'. Gyro is designed as an electronically driven tuning fork, often fabricated out of a single piece of quartz or silicon. Such gyros operate in accordance with the dynamic theory that when an angle rate is applied to a translating body, a Coriolis force is generated.
Current state of the art non-military technology (as of 2005[update]) can build small solid state sensors that can measure human body movements. These devices have no moving parts, and weigh about 50 grams.
Solid state devices using the same physical principles are used for image stabilization in small cameras or camcorders. These can be extremely small (≈5 mm) and are built with Microelectromechanical systems (MEMS) technologies.
Its detailed here: 
Sensors based on magnetohydrodynamic principles can be used to measure angular velocities.
|23px||This section is empty. You can help by adding to it. (March 2015)|
Ring Laser Gyros (RLG)
A ring laser gyro splits a beam of laser light into two beams in opposite directions through narrow tunnels in a closed optical circular path around the perimeter of a triangular block of temperature-stable Cervit glass with reflecting mirrors placed in each corner. When the gyro is rotating at some angular rate, the distance traveled by each beam becomes different—the shorter path being opposite to the rotation. The phase-shift between the two beams can be measured by an interferometer, and is proportional to the rate of rotation (Sagnac effect).
In practice, at low rotation rates the output frequency can drop to zero after the result of backscattering causing the beams to synchronise and lock together. This is known as a lock-in, or laser-lock. The result is that there is no change in the interference pattern, and therefore no measurement change.
To unlock the counter-rotating light beams, laser gyros either have independent light paths for the two directions (usually in fiber optic gyros), or the laser gyro is mounted on a piezo-electric dither motor that rapidly vibrates the laser ring back and forth about its input axis through the lock-in region to decouple the light waves.
The shaker is the most accurate, because both light beams use exactly the same path. Thus laser gyros retain moving parts, but they do not move as far.
Fiber optic gyros (FOG)
A more recent variation on this, the fiber optic gyroscope, uses an external laser and two beams going opposite directions (counter-propagating)in long spools (several kilometers) of fiber optic cable, with the phase difference of the two beams compared after their travel through the spools of fiber.
The basic mechanism, monochromatic laser light travelling in opposite paths, and the Sagnac effect, is the same in a FOG and a RLG, but the engineering details are substantially different compared to earlier laser gyros.
Precise winding of the fiber-optic coil is required to ensure the paths taken by the light in opposite directions is as similar as possible. The FOG requires more complex calibrations than a Laser ring gyro making the development and manufacture of FOG's more technically challenging that for a RLG. However FOG's do not suffer from laser lock at low speeds and do not need to contain any moving parts, increasing the maximum potential accuracy and lifespan of a FOG over an equivalent RLG.
The basic, open-loop accelerometer consists of a mass attached to a spring. The mass is constrained to move only in-line with the spring. Acceleration causes deflection of the mass and the offset distance is measured. The acceleration is derived from the values of deflection distance, mass, and the spring constant. The system must also be damped to avoid oscillation. A closed-loop accelerometer achieves higher performance by using a feedback loop to cancel the deflection, thus keeping the mass nearly stationary. Whenever the mass deflects, the feedback loop causes an electric coil to apply an equally negative force on the mass, canceling the motion. Acceleration is derived from the amount of negative force applied. Because the mass barely moves, the non-linearities of the spring and damping system are greatly reduced. In addition, this accelerometer provides for increased bandwidth past the natural frequency of the sensing element.
Both types of accelerometers have been manufactured as integrated micro-machinery on silicon chips.
TIMU (Timing & Inertial Measurement Unit) sensors
DARPA's Microsystems Technology Office( MTO) department is working on a Micro-PNT ("Micro-Technology for Positioning, Navigation and Timing") program to design "TIMU" ("Timing & Inertial Measurement Unit") chips that does absolute position tracking on a single chip without GPS aided navigation.
Micro-PNT adds a highly accurate master timing clock integrated into an IMU (Inertial Measurement Unit) chip, making it a "TIMU" ("Timing & Inertial Measurement Unit") chip. So these TIMU chips for Micro-PNT have integrated 3-axis gyroscope, 3-axis accelerometer, and 3-axis magnetometer, and together with the integrated highly accurate master timing clock it simultaneous measure the motion tracked and combines that with timing from the synchronized clock, and with sensor fusion it makes a single chip that does absolute position tracking, all without external transmitters/transceivers.
In one form, the navigational system of equations acquires linear and angular measurements from the inertial and body frame, respectively and calculates the final attitude and position in the NED frame of reference.
Where: f is specific force, <math>\omega</math> is angular rate, a is acceleration, R is position, <math> \dot R </math> and V are velocity, <math>\Omega</math> is the angular velocity of the earth, g is the acceleration due to gravity, <math>\Phi, \lambda</math> and h are the NED location parameters. Also, super/subscripts of E, I and B are representing variables in the Earth centered, Inertial or Body reference frame, respectively and C is a transformation of reference frames.
- Adam Air Flight 574
- Attitude control
- Dead reckoning
- Fibre optic gyroscope
- Guidance system
- Inertial measurement unit (IMU)
- Kalman filter
- Korean Air Lines Flight 007
- PIGA accelerometer
- Quantum compass
- Rate integrating gyroscope
- Schuler tuning
- LN-3 Inertial Navigation System
- Genesis of the Litton Inertial Navigation System
- "Basic Principles of Inertial Navigation Seminar on inertial navigation systems." (PDF). AeroStudents.com. Tampere University of Technology, page 5. Retrieved 22 January 2015.
- Google Books
- Eshbach's Handbook of Engineering Fundamentals By Ovid W. Eshbach, Byron pg 9
- Doug Weed, et al.: GPS Align in Motion of Civilian Strapdown INS. Honeywell Commercial Aviation Products.
- The Hemispherical Resonator Gyro: From Wineglass to the Planets, David M. Rozelle
- http://www.darpa.mil/Our_Work/MTO/Programs/Micro-Technology_for_Positioning,_Navigation_and_Timing_%28Micro-PNT%29.aspx Micro-Technology for Positioning, Navigation and Timing (Micro-PNT)
- http://www.darpa.mil/NewsEvents/Releases/2013/04/10.aspx Extreme Miniaturization: Seven Devices, One Chip to Navigate without GPS
- http://www.darpa.mil/NewsEvents/Releases/2012/09/20.aspx Microfabrication methods to help navigate a day without GPS
- http://www.darpa.mil/Our_Work/MTO/Programs/Micro-Technology_Positioning,_Navigation_and_Timing_%28Micro-PNT%29/Clocks.aspx Micro-PNT - Clocks
- Sherryl H. Stovall Basic Inertial Navigation, Naval Air Warfare Center Weapons Division, September 1997
- Space guidance evolution
- A.D. King (1998). "Inertial Navigation – Forty Years of Evolution" (PDF). GEC Review (General Electric Company plc) 13 (3): 140–149.
- Principle of operation of an accelerometer
- Overview of inertial instrument types
- E. v. Hinueber (iMAR Navigation) (2011). "Design of an Unaided Aircraft Attitude Reference System with Medium Accurate Gyroscopes for Higher Performance Attitude Requirements". Inertial Sensors and Systems - Symposium Gyro Technology, Karlsruhe / Germany (iMAR Navigation / DGON) 2011.
- Oxford Technical Solutions Inertial Navigation Guide