|40x40px||Look up joist in Wiktionary, the free dictionary.|
In architecture and engineering, a joist is one of the horizontal supporting members that run between foundations, walls, or beams to support a ceiling or floor. They may be made of wood, engineered wood, steel, or concrete. Typically a joist has the cross section of a plank, while a beam is bigger than a joist. Joists are often supported by beams laid out in repetitive patterns.
Band sill, box sill or rim joist is a term for the joist along the outside edges of the floor system in the United States.
Joists need to be designed large enough to support the anticipated load over a long period of time and in some countries such as the United States to meet standards for stiffness. The wider the span between the supporting structures, the deeper the joist will need to be if it is not to deflect under load. Lateral support called dwang, blocking, or strutting also increases its strength. There are approved formulas for calculating the depth required and reducing the depth as needed; however, a rule of thumb for calculating the depth of a wooden floor joist for a residential property is half the span in feet plus two inches; for example, the joist depth required for a 14‑foot span is 9 inches. Many steel joist manufacturers supply load tables in order to allow designers to select the proper joist sizes for their projects.
Engineered wood products such as I-joists gain strength from the depth of the floor or the height of each joist, as well as the larger bottom and top chords, as compared to standard dimensional lumber joists. A common saying regarding structural design is that "deeper is cheaper", referring to the more cost-effective design of a given structure by using deeper but more expensive joists, because fewer joists needed and longer spans are achieved, which more than makes up for the added cost of deeper joists.
In traditional timber framing there may be a single set of joists which carry both a floor and ceiling called a single floor (single joist floor, single framed floor) or two sets of joists, one carrying the floor and another carrying the ceiling called a double floor (double framed floor). The term binding joist is sometimes used to describe beams at floor level running perpendicular to the ridge of a gable roof and joined to the intermediate posts. Joists which land on a binding joist are called bridging joists. A large beam in the ceiling of a room carrying joists is a summer beam. A ceiling joist may be installed flush with the bottom of the beam or sometimes below the beam. Joists left exposed and visible from below are called "naked flooring" or "articulated" (a modern U.S. term) and were typically planed smooth (wrought) and sometimes chamfered or beaded.
Connections to supporting beams
Joists may join to their supporting beams in many ways: joists resting on top of the supporting beams are said to be "lodged"; dropped in using a butt cog joint (a type of lap joint), half-dovetail butt cog, or a half-dovetail lap joint. Joists may also be tenoned in during the raising with a soffit tenon or a tusk tenon (possibly with a housing). Joists can also be joined by being slipped into mortises after the beams are in place such as a chase mortise (pulley mortise), L-mortise, or "short joist". Also, in some Dutch-American work, ground level joists are placed on a foundation and then a sill placed on top of the joists such as what timber frame builder Jack Sobon called an "inverted sill" or with a "plank sill".
Joists can have different joints on either ends such as being tenoned on one end and lodged on the other end. A reduction in the under-side of cogged joist-ends may be square, sloped or curved. Typically joists do not tie the beams together, but sometimes they are pinned or designed to hold under tension. Joists on the ground floor were sometimes a pole (pole joist, half-round joist, log joist. A round timber with one flat surface) and in barns long joists were sometimes supported on a sleeper (a timber not joined to but supporting other beams). Joists left out of an area form an opening called a "well" as in a stairwell or chimney-well. The joists forming the well are the heading joist (header) and trimming joist (trimmer). Trimmers take the name of the feature such as hearth trimmer, stair trimmer, etc.
Shortened joists are said to be crippled. The term rim joist is rare before the 1940s in America; it forms the edge of a floor. The outermost joist in half timber construction may be of a more durable species than the interior joists. In a barn, loose poles above the drive floor are called a scaffold. Between the joists, the area called a joist-bay, and above the ceiling in some old houses is material called pugging, which was used to deaden sound, insulate, and resist the spread of fire.
|40x40px||Wikimedia Commons has media related to Joists.|
- Ventolo, William L.. Your home inspection guide. Chicago, Ill.: Real Estate Education Co., 1995. 225. Print.
- Fleming, Eric. Construction technology: an illustrated introduction. Oxford: Blackwell, 2005. 105. Print.
- Emmitt, Stephen, R. Barry, and Christopher A. Gorse. Barry's advanced construction of buildings. 2nd ed. Chichester, U.K.: Wiley-Blackwell, 2010. 3-94. Print.
- A Glossary of Terms used in the Grecian, Roman, Italian and Gothic Architecture
- "joist" def. 1. Oxford English Dictionary Second Edition on CD-ROM (v. 4.0) © Oxford University Press 2009