Open Access Articles- Top Results for Mk 2 grenade

Mk 2 grenade

Template:Infobox Weapon

The Mk 2 grenade (sometimes written Mk II) is a fragmentation type anti-personnel hand grenade introduced by the U.S. armed forces in 1918. It was the standard issue anti-personnel grenade used during World War II and in later conflicts, including the Vietnam War. Replacing the failed Mk I of 1917, it was standardized in 1920, and redesignated the Mk 2 in 1945.

The Mk.2 was replaced by the M26-series (M26/M61/M57) and later M33 series (M33/M67). It was phased out gradually in service beginning with the Korean War. Due to the tremendous quantity manufactured during World War 2, it was in limited standard issue with the US Army and US Marine Corps throughout the 1950s and 1960s. The U.S. Navy was one of the last users when it was discontinued in the 1970s.


The Mk II was manufactured with grooves in the cast iron to enhance fragmentation and provid a better grip handling and throwing the grenade. These gave it the appearance of a pineapple and origin of that nickname. It was also commonly referred to as a "frag" grenade, in contrast to the MK3 concussion grenade.

The original Mk II grenade had a 3/8" threaded plug in its base covering the opening used to place the explosive filling. The improved "Mk IIA1" (a designation used informally by armorers, historians, and collectors but was never officially by the US military[1]) introduced in 1942 was filled through the fuse well instead.

Low explosive Mk. II grenades were filled with smokeless EC powder powder, which produced an adequate amount of fragmentation and did away with the need of a detonator. It was initially replaced by a small length of safety fuse terminated with a black powder igniter charge. Production grenades with the EC powder filler used the M10 series of igniting fuse.

High Explosive Mk. II's used flaked or granular TNT. Pre-war Mk. IIs with a TNT filler were identified with an all-yellow body as a warning to users. Wartime grenades were repainted olive drab for camouflage purposes with a narrow yellow band below the fuse. Repainted grenades usually lacked the yellow band.

The Mk. II used the M5, M6, and M10 series fuses. These early fuses made a loud "bang" and produced sparks when activated. They had other problems as well. The M10-series' powder train made a "hissing" sound as it burned, potentially alerting the enemy of its presence. The M5 and M6 series sometimes prematurely detonated when the flash from the primer hit the TNT charge rather than the delay fuse. Moisture could get in under the foil fuse cap, causing the weapon to fail to detonate. Improved smokeless and (almost) silent fuses (like the M204-series) were later fitted after World War II.


Mk. II Grenades came 25 to a wooden crate and were shipped in fiberboard packing tubes. TNT grenades, like all High Explosive devices, were shipped unfused to prevent premature detonation. Their fuses were shipped separately and came in flat cardboard boxes of 25. EC Powder grenades were shipped with their fuses attached.

Variants included:

  • Grenade, Hand, Fragmentation, Mk II: EC powder filler, uses M11 or M10A1 igniting fuse.
  • Grenade, Hand, Fragmentation, Mk IIA1: EC powder filler, uses M10A2 igniting fuse. Has no baseplug because it was filled through the fuse well.
  • Grenade, Hand, Fragmentation, HE, Mk II: TNT filler, uses M5 detonating fuse.
  • Grenade, Hand, TNT, Fragmentation, Mk II: TNT filler, uses M6A4C detonating fuse.
  • Grenade, Hand, Practice, Mk II: Black Powder "spotting" charge in a cardboard tube connected to a M10-series igniting fuse. Has a standard body with a wooden or cork baseplug that popped out during detonation, creating a loud report (i.e., "BANG" noise) and smoke to indicate ignition. The body would be reused and reloaded as long as it remained intact.
  • Grenade, Hand, Practice, M21: Black Powder "spotting" charge, uses M10-series igniting fuse. Has a heavier body and no baseplug. Its body was embossed with the vertical letters "R" "D" and "X" on the knobs in a column on one side (because it was originally designed to be for an HE grenade with a more powerful RDX filler). When detonated, it made a loud report and smoke came out of the fuse vents.


  • Body: Made of cast-iron with a grooved surface that is divided into 40 knobbed segments in 5 rows of 8 columns. Models made from 1918 to 1942 have a 3/4"-threaded baseplug to insert or remove the explosive filler. Models made from 1942 onwards were filled through the fuse well to speed up production.
  • Fuse: Dependent on variant, includes M5 and M6 detonating fuses (for Mk.2s with a High Explosive filler), and M10 igniting fuses (for Mk.2s with an EC Black Powder filler). The delay time was 4 to 5 seconds.
  • Charge: Either a Low Explosive (EC powder) or High Explosive (flaked or granular TNT) filler.
  • Markings: Low Explosive grenades were made of blackened iron or were painted Gray or Black to prevent rust. Pre-war High Explosive grenades were painted Yellow; wartime grenades (c.1942 and onward) were overpainted or painted Olive Drab with a Yellow ring at the top. Mk. II Practice grenades (c.1920-1945) were painted Red (a practice copied from the French military). M21 Practice grenades (c.1945 to 1950s) were painted light Blue (a practice copied from the British military) and had blue-painted fuse levers.


See also

Notes and references

  • Gervasi, Tom. Arsenal of Democracy II: American Military Power in the 1980s and the Origins of the New Cold War: with a Survey of American Weapons and Arms Exports. New York: Grove Press, 1981. ISBN 0-394-17662-6.
  • War Department. Field Manual FM 23-30-1944 Hand and Rifle Grenades; Rocket, AT, HE, 2.36" (February, 1944); pgs. 5-6.

External links