Oleum - Related Links
Open Access Articles- Top Results for Oleum
Journal of Petroleum & Environmental EngineeringPlasmid Curing of a Novel Hydrocarbon Degrading Bacillus cereus Strain DRDU1 Revealed its Involvement in Petroleum Oil Degradation
Journal of Petroleum & Environmental EngineeringA Method of Central Composite Design (CCD) For Optimization of Biodiesel Production from Chlorella vulgaris
Journal of Petroleum & Environmental EngineeringProduction of Biodiesel from Waste Vegetable Oil via KM Micro-mixer
Journal of Petroleum & Environmental EngineeringSaving Petroleum using Smart Strategies
Journal of Petroleum & Environmental EngineeringPlanning UBD in Horizontal Well to Minimize Formation Damage
- For the community in California, see Oleum, California.
Oleum (Latin oleum = "oil"), or fuming sulfuric acid, is a solution of various compositions of sulfur trioxide in sulfuric acid, or sometimes more specifically to disulfuric acid (also known as pyrosulfuric acid).
Oleums can be described by the formula ySO3.H2O where y is the total molar sulfur trioxide content. The value of y can be varied, to include different oleums. They can also be described by the formula H2SO4.xSO3 where x is now defined as the molar free sulfur trioxide content. Oleum is generally assayed according to the free SO3 content by weight. It can also be expressed as a percentage of sulfuric acid strength; for oleum concentrations, that would be over 100%. For example, 10% oleum can also be expressed as H2SO4.0.13611SO3, 1.0225SO3.H2O or 102.25% sulfuric acid. The conversion between % acid and % oleum is: % acid = 100 + 18/80 * % oleum
A value for x of 1 gives us the empirical formula H2S2O7 for disulfuric (pyrosulfuric) acid. Pure disulfuric acid itself is a solid at room temperature, melting at 36 °C and rarely used either in the laboratory or industrial processes.
|This section does not cite any references or sources. (October 2010)|
Oleum is produced in the contact process, where sulfur is oxidized to sulfur trioxide which is subsequently dissolved in concentrated sulfuric acid. Sulfuric acid itself is regenerated by dilution of part of the oleum.
The lead chamber process for sulfuric acid production was abandoned partly because it could not produce sulfur trioxide or concentrated sulfuric acid directly due to corrosion of the lead, and absorption of NO2 gas. Until this process was made obsolete by the contact process, oleum had to be obtained through indirect methods. Historically, the biggest production of oleum came from the distillation of iron sulfates at Nordhausen, from which the historical name Nordhausen sulfuric acid is derived.
Sulfuric acid production
Oleum is an important intermediate in the manufacture of sulfuric acid due to its high enthalpy of hydration. When SO3 is added to water, rather than simply dissolving, it tends to form a fine mist of sulfuric acid, which is difficult to manage. However, SO3 added to concentrated sulfuric acid readily dissolves, forming oleum which can then be diluted with water to produce additional concentrated sulfuric acid.
As an intermediate for transportation
Oleum is a useful form for transporting sulfuric acid compounds, typically in rail tankcars, between oil refineries (which produce various sulfur compounds as a byproduct of refining) and industrial consumers.
Certain compositions of oleum are solid at room temperature, and thus are safer to ship than when liquid. Solid oleum can then be converted into liquid at the destination through steam heating or dilution or concentration. This requires some care to prevent overheating and evaporation of sulfur trioxide. To extract it from a tank car requires careful heating using steam conduits within the tank car. Great care must be taken to avoid overheating, as this can increase the internal pressure within the tank car to a value exceeding the limit of the tank's safety valve.
In addition, oleum is less corrosive to metals than sulfuric acid, because there is no free water to attack the surfaces. Because of that, sulfuric acid is sometimes concentrated to oleum for in-plant pipelines and then diluted back to acid for use in industrial reactions.
In Richmond, California in 1993 a significant release occurred due to overheating, causing a release of sulfur trioxide that absorbed moisture from the atmosphere, creating a mist of micrometre-sized sulfuric acid particles that formed an inhalation health hazard. This mist produced adverse health effects on residents and workers over a wide area.
Oleum is a harsh reagent, and is highly corrosive. One important use of oleum as a reagent is the secondary nitration of nitrobenzene. The first nitration can occur with nitric acid in sulfuric acid, but this deactivates the ring towards further electrophilic substitution. A stronger reagent, oleum, is needed to introduce the second nitro group onto the aromatic ring.
Oleum is used in the manufacture of many explosives with the notable exception of nitrocellulose. (In modern manufacturing of Nitrocellulose, the H2SO4 concentration is often adjusted using Oleum) The chemical requirements for explosives manufacture often call for anhydrous mixtures containing nitric acid and sulfuric acid. Ordinary commercial grade nitric acid consists of the constant boiling azeotrope of nitric acid and water, and contains 68% nitric acid. Mixtures of ordinary nitric acid in sulfuric acid therefore contain substantial amounts of water and are unsuitable for processes such as occur in the manufacture of trinitrotoluene.
Anhydrous nitric acid, referred to as white fuming nitric acid, can be used to prepare water-free nitration mixtures, and this method is used in laboratory scale operations where the cost of material is not of primary importance. Fuming nitric acid is very hazardous to handle and transport, because it is extremely corrosive and volatile. For industrial use, such strong nitration mixtures are prepared by mixing oleum with ordinary commercial nitric acid so that the free sulfur trioxide in the oleum consumes the water in the nitric acid.
Like concentrated sulfuric acid, oleum is such a strong dehydrating agent that if poured onto powdered glucose, or virtually any other sugar, it will draw the elements of water out of the sugar in an exothermic reaction, leaving nearly pure carbon as a solid. This carbon expands outward, hardening as a solid black substance with gas bubbles in it.
- Considine, Douglas M., Chemical and Process Technology Encyclopedia, McGraw-Hill, 1974, pp 1070–1.
- Major Accidents at Chemical/Refinery Plants in Contra Costa County
- Baskett, R. L., Vogt, P. J., Schalk III, Pobanz, B. M., "ARAC Dispersion Modeling of the July 26, 1993 Oleum Tank Car Spill in Richmond, California", UCRL-ID-116012, February 3, 1994
- CASE STUDY – Richmond, California Oleum Release (EPIcode – a chemical dispersion modeling software product)
- Urbanski, Tadeusz, Chemistry and Technology of Explosives, Pegamon Press, Oxford, 1965, Vol 2, pp 329.
- Urbanski, Vol 1, pp 347–349