Open Access Articles- Top Results for POWER6


Produced 2007
Designed by IBM
Max. CPU clock rate 3.6 GHz to 5.0 GHz
Min. feature size 65 nm
Instruction set Power Architecture (Power ISA v.2.05)
Cores 2
L1 cache 64+64 KB/core
L2 cache 4 MB/core
L3 cache 32 MB/chip (off-chip)
Predecessor POWER5
Successor POWER7

The POWER6 is a microprocessor developed by IBM that implemented the Power ISA v.2.03. When it became available in systems in 2007, it succeeded the POWER5+ as IBM's flagship Power microprocessor. It is part of the eCLipz project, said to have a goal of converging IBM's server hardware where practical (hence "ipz" in the acronym: iSeries, pSeries, and zSeries).[1]


POWER6 was described at the International Solid-State Circuits Conference (ISSCC) in February 2006, and additional details were added at the Microprocessor Forum in October 2006 [1] and at the next ISSCC in February 2007. It was formally announced on May 21, 2007.[2] It was released on June 8, 2007 at speeds of 3.5, 4.2 and 4.7 GHz,[2] but the company has noted prototypes have reached 6 GHz.[3] POWER6 reached first silicon in the middle of 2005,[4] and was bumped to 5.0 GHz in May 2008 with the introduction of the P595.[5]


The POWER6 is a dual-core processor. Each core is capable of two-way simultaneous multithreading (SMT). The POWER6 has approximately 790 million transistors and is 341 mm2 large fabricated on a 65 nm process. A notable difference from POWER5 is that the POWER6 executes instructions in-order instead of out-of-order. This change often requires software to be recompiled for optimal performance, but the POWER6 still achieves significant performance improvements over the POWER5+ even with unmodified software, according to the lead engineer on the POWER6 project.[2]

POWER6 also takes advantage of ViVA-2, Virtual Vector Architecture, which enables the combination of several POWER6 nodes to act as a single vector processor.[6]

Each core has two integer units, two binary floating-point units, an AltiVec unit, and a novel decimal floating-point unit. The binary floating-point unit incorporates “many microarchitectures, logic, circuit, latch and integration techniques to achieve [a] 6-cycle, 13-FO4 pipeline,” according to a company paper.[7] Unlike the servers from IBM's competitors, the POWER6 has hardware support for IEEE 754 decimal arithmetic and includes the first decimal floating-point unit integrated in silicon. More than 50 new floating point instructions handle the decimal math and conversions between binary and decimal.[8] This feature was also added to the z10 microprocessor featured in the System z10.[6]

Each core has a 64 KB, four-way set-associative instruction cache and a 64 KB data cache of an eight-way set-associative design with a two-stage pipeline supporting two independent 32-bit reads or one 64-bit write per cycle.[7] Each core has semi-private 4 MiB unified L2 cache, where the cache is assigned a specific core, but the other has a fast access to it. The two cores share a 32 MiB L3 cache which is off die, using an 80 GB/s bus.[8]

POWER6 can connect to up to 31 other processors using two inter node links (50 GB/s), and supports up to 10 logical partitions per core (up to a limit of 254 per system). There is an interface to a service processor that monitors and adjusts performance and power according to set parameters.[9]

IBM also makes use of a 5 GHz duty-cycle correction clock distribution network for the processor. In the network, the company implements a copper distribution wire that is 3 µm wide and 1.2 µm thick. The POWER6 design uses dual power supplies, a logic supply in the 0.8-to-1.2 Volt range and an SRAM power supply at about 150-mV higher.[7]

The thermal characteristics of POWER6 are similar to that of the POWER5. Dr Frank Soltis, an IBM chief scientist, said IBM had solved power leakage problems associated with high frequency by using a combination of 90 nm and 65 nm parts in the POWER6 design.[10]


The slightly enhanced POWER6+ was introduced in April 2009, but had been shipping in Power 560 and 570 systems since October 2008. It added more memory keys for secure memory partition, a feature taken from IBM's mainframe processors.[11]


As of 2008, the range of POWER6 systems includes "Express" models (the 520, 550 and 560) and Enterprise models (the 570 and 595).[3] The various system models are designed to serve any sized business. For example, the 520 Express is marketed to small businesses while the Power 595 is marketed for large, multi-environment data centers. The main difference between the Express and Enterprise models is that the latter include Capacity Upgrade on Demand (CUoD) capabilities and hot-pluggable processor and memory "books".

IBM POWER6 servers
Name Number of sockets Number of cores CPU clock frequency
520 Express 2 4 4.2 GHz or 4.7 GHz
550 Express 4 8 4.2 GHz or 5.0 GHz
560 Express 8 16 3.6 GHz
570 8 16 4.4 GHz or 5.0 GHz
570 16 32 4.2 GHz
575 16 32 4.7 GHz
595 32 64 4.2 GHz or 5.0 GHz

IBM also offers four POWER6 based blade servers.[4] Specifications are shown in the table below.

IBM POWER6 blade servers
Name Number of cores CPU clock frequency Blade slots required
BladeCenter JS12 2 3.8 GHz 1
BladeCenter JS22 4 4.0 GHz 1
BladeCenter JS23 4 4.2 GHz 1
BladeCenter JS43 8 4.2 GHz 2

All blades support AIX, i, and Linux. The BladeCenter S and H chassis is supported for blades running AIX, i, and Linux. The BladeCenter E, HT, and T chassis support blades running AIX and Linux but not i.

At the SuperComputing 2007 (SC07) conference in Reno a new water-cooled Power 575 was revealed. The 575 is composed of 2U "nodes" each with 32 POWER6 cores at 4.7 GHz with up to 256 GB of RAM. Up to 448 cores can be installed in a single frame.

IBM POWER6 disk storage
Name Number of cores CPU clock frequency Number of controllers
DS8700 2, 4 4.7 GHz 1, 2
DS8800 2, 4, 8 5.0 GHz 1, 2

See also


External links

Recommended reading