|This article needs additional citations for verification. (March 2010)|
Radio control (often abbreviated to R/C or simply RC) is the use of radio signals to remotely control a device. Radio control is used for control of model vehicles from a hand-held radio transmitter. Industrial, military, and scientific research organizations make use of radio-controlled vehicles as well.
In 1898 at an exhibition at Madison Square Garden Nikola Tesla demonstrated a small unmanned boat that was radio controlled. In a bit of showmanship Tesla entertained the audience to make it seem that the boat could apparently obey commands from the audience but was in fact controlled by Tesla interpreting the verbal requests and sending appropriate frequencies to tuned circuits in the boat. John Hays Hammond Jr is regarded as the father of radio control due to experiments as an apprentice of Thomas Edison at the age of twelve. Hammond was a close friend of Tesla and they performed experiments together in his lab located in his castle. He learned a great deal from his exposure to Tesla. Tesla was granted a US patent on this invention on July 1st, 1898. In 1903, the Spanish engineer Leonardo Torres y Quevedo presented the "Telekino" at the Paris Academy of Science, and was granted a patent in France, Spain, Great Britain and the United States. In 1904, Bat, a Windermere steam launch, was controlled using experimental radio control by its inventor, Jack Kitchen.
In 1909 the French inventor Gabet demonstrated what he called his "Torpille Radio-Automatique", a radio controlled torpedo. In 1917, Archibald Low as head of the RFC Experimental Works, was the first person to use radio control successfully on an aircraft.
In the 1920s, various radio-controlled ships were used for naval artillery target practice. In 1922, the obsolete, US Navy battleship USS Iowa became the first of these target ships. Radio control gear, developed by the radio engineer John Hays Hammond, Jr., was installed before her sinking in gunnery exercise in March 1923.
The Soviet Red Army used remotely controlled teletanks during the 1930s in the Winter War against Finland and fielded at least two teletank battalions at the beginning of the Great Patriotic War. A teletank is controlled by radio from a control tank at a distance of 500–1,500 meters, the two constituting a telemechanical group. There were also remotely controlled cutters and experimental remotely controlled planes in the Red Army. In the 1930s Britain developed the radio controlled Queen Bee, a remotely controlled unmanned Tiger Moth aircraft for a fleet's gunnery firing practice. The Queen Bee was superseded by the similarly named Queen Wasp, a later, purpose built, target aircraft of higher performance.
Military applications in the Second World War
Radio control was further developed during World War II, primarily by the Germans who used it in a number of missile projects. Their main effort was the development of radio-controlled missiles and glide bombs for use against shipping, a target that is otherwise both difficult and dangerous to attack. However by the end of the war the Luftwaffe was having similar problems attacking Allied bombers, and developed a number of radio command guided anti-aircraft missiles, none of which saw service.
The effectiveness of the Luftwaffe's systems — primarily comprising the series of Telefunken Funk-Gerät (or FuG) 203 Kehl twin-axis, single joystick-equipped transmitters mounted in the deploying aircraft, and Telefunken's companion FuG 230 Straßburg receiver placed in the ordnance to be controlled during deployment — and used by both the Fritz X unpowered, armored anti-ship bomb, and the powered Henschel Hs 293 guided bomb, was greatly reduced by British efforts to jam their radio signals, eventually with American assistance. After initial successes, the British launched a number of commando raids to collect the missile radio sets. Jammers were then installed on British ships, and the weapons basically "stopped working". The German development teams then turned to wire guidance once they realized what was going on, but these systems were not ready for deployment until the war had already moved to France.
Both the British and US also developed radio control systems for similar tasks, in order to avoid the huge anti-aircraft batteries set up around German targets. However, none of these systems proved usable in practice, and the one major US effort, Operation Aphrodite, proved to be far more dangerous to its users than to the target. The American Azon guided free-fall ordnance, however, did prove somewhat useful in both the European and CBI Theaters of World War II.
Radio control systems of this era were generally electromechanical in nature, using small metal "fingers" or "reeds" with different resonant frequencies each of which would operate one of a number of different relays when a particular frequency was received. The relays would in turn then activate various actuators acting on the control surfaces of the missile. The controller's radio transmitter would transmit the different frequencies in response to the movements of a control stick; these were typically on/off signals. The radio gear used to control the rudder function on the American-developed Azon guided ordnance, however, was a fully proportional control, with the "ailerons", solely under the control of an on-board gyroscope, serving merely to keep the ordnance from rolling.
These systems were widely used until the 1960s, when the increasing use of solid state systems greatly simplified radio control. The electromechanical systems using reed relays were replaced by similar electronic ones, and the continued miniaturization of electronics allowed more signals, referred to as control channels, to be packed into the same package. While early control systems might have two or three channels using amplitude modulation, modern systems include 20 or more using frequency modulation.
The first general use of radio control systems in models started in the early 1950s with single-channel self-built equipment; commercial equipment came later. The advent of transistors greatly reduced the battery requirements, since the current requirements at low voltage were greatly reduced and the high voltage battery was eliminated. In both tube and early transistor sets the model's control surfaces were usually operated by an electromagnetic escapement controlling the stored energy in a rubber-band loop, allowing simple on/off rudder control (right, left, and neutral) and sometimes other functions such as motor speed.
Crystal-controlled superheterodyne receivers with better selectivity and stability made control equipment more capable and at lower cost. Multi-channel developments were of particular use to aircraft, which really needed a minimum of three control dimensions (yaw, pitch and motor speed), as opposed to boats, which required only two or one.
As the electronics revolution took off, single-signal channel circuit design became redundant, and instead radios provided proportionally coded signal streams which a servomechanism could interpret, using pulse-position modulation (PPM).
More recently, high-end hobby systems using Pulse-code modulation (PCM) features have come on the market that provide a computerized digital bit-stream signal to the receiving device, instead of the earlier PPM encoding type. However, even with this coding, loss of transmission during flight has become more common, in part because of the ever more wireless society. Some more modern FM-signal receivers that still use "PPM" encoding instead can, thanks to the use of more advanced computer chips in them, be made to lock onto and use the individual signal characteristics of a particular PPM-type RC transmitter's emissions alone, without needing a special "code" transmitted along with the control information as PCM encoding has always required.
In the early 21st century, 2.4 gigahertz spread spectrum RC control systems have become increasingly utilized in control of model vehicles and aircraft. Now, these 2.4 GHz systems are being made by most radio manufacturers. These radio systems range from a couple thousand dollars, all the way down to under US$30 for some. Some manufacturers even offer conversion kits for older digital 72 MHz receivers and radios. As the emerging multitude of 2.4 GHz band spread spectrum RC systems usually use a "frequency-agile" mode of operations, like FHSS that do not stay on one set frequency any longer while in use, the older "exclusive use" provisions at model flying sites needed for VHF-band RC control systems's frequency control, for VHF-band RC systems that only used one set frequency unless serviced to change it, are not as mandatory as before.
Modern military and aerospace applications
Remote control military applications are typically not radio control in the direct sense, directly operating flight control surfaces and propulsion power settings, but instead take the form of instructions sent to a completely autonomous, computerized automatic pilot. Instead of a "turn left" signal that is applied until the aircraft is flying in the right direction, the system sends a single instruction that says "fly to this point".
Industrial radio remote control
Today radio control is used in industry for such devices as overhead cranes and switchyard locomotives. Radio-controlled teleoperators are used for such purposes as inspections, and special vehicles for disarming of bombs. Some remotely controlled devices are loosely called robots, but are more properly categorized as teleoperators since they do not operate autonomously, but only under control of a human operator.
An industrial radio remote control can either be operated by a person, or by a computer control system in a machine to machine (M2M) mode. For example, an automated warehouse may use a radio-controlled crane that is operated by a computer to retrieve a particular item. Industrial radio controls for some applications, such as lifting machinery, are required to be of a fail-safe design in many jurisdictions.
Industrial remote controls work differently from most consumer products. When the receiver receives the radio signal which the transmitter sent, it checks it so that it is the correct frequency and that any security codes match. Once the verification is complete, the receiver sends an instruction to a relay which is activated. The relay activates a function in the application corresponding to the transmitters button. This could be to engage an electrical directional motor in an overhead crane. In a receiver there are usually several relays, and in something as complex as an overhead crane, perhaps up to 12 or more relays are required to control all directions. In a receiver which opens a gate, two relays are often sufficient.
- Precision-guided munition
- Radio-controlled airplane
- Radio-controlled boat
- Radio-controlled car
- Radio-controlled helicopter
- Radio-controlled model
- Remote control
- Remote control vehicle
Notes and references
- Tapan K. Sarkar, History of wireless, John Wiley and Sons, 2006 ISBN 0-471-71814-9 pages 276-278
- Sarkar 2006, page 97
- Gabet and his Torpille
- "Coast Battleship No. 4 (ex-USS Iowa, Battleship # 4) -- As a Target Ship, 1921–1923". Online Library of Selected Images:U.S. NAVY SHIPS. Naval History and Heritage Command. 13 April 2003. Retrieved 21 May 2012.
- http://www.rcmodelswiz.co.uk/users-basic-guide-to-radio-control-systems RC Models Wiz: Basic Guide to Radio Control Systems.
- Autec srl. "Radio Remote Control Safety" (PDF). Retrieved 18 November 2013.
- Tele Radio AB. "What is industrial remote control". Retrieved 14 November 2014.
|40x40px||Wikimedia Commons has media related to Radio Control.|
|40x40px||Look up radio control in Wiktionary, the free dictionary.|
- Bill Yenne, Attack of the drones: a history of unmanned aerial combat, Zenith Imprint, 2004, ISBN 0-7603-1825-5
- Laurence R. Newcome Unmanned aviation: a brief history of unmanned aerial vehicles, AIAA, 2004, ISBN 1-56347-644-4,
Lua error in Module:Authority_control at line 346: attempt to index field 'wikibase' (a nil value).pl:Zdalne sterowanie