Open Access Articles- Top Results for Static random-access memory

Static random-access memory

Not to be confused with SDRAM or "Synchronous DRAM".
File:Hyundai RAM HY6116AP-10.jpg
A static RAM chip from a NES clone (2K x 8 bit)

Static random-access memory (SRAM or static RAM) is a type of semiconductor memory that uses bistable latching circuitry to store each bit. The term static differentiates it from dynamic RAM (DRAM) which must be periodically refreshed. SRAM exhibits data remanence,[1] but it is still volatile in the conventional sense that data is eventually lost when the memory is not powered.

Applications and uses

SRAM cells on the die of a STM32F103VGT6 microcontroller as seen by a scanning electron microscope. Manufactured by STMicroelectronics using a 180 nanometre process.
Comparison image of 180 nanometre SRAM cells on a STM32F103VGT6 microcontroller as seen by an optical microscope.


  • SRAM is more expensive and less dense than DRAM and is therefore not used for high-capacity, low-cost applications such as the main memory in personal computers.

Clock rate and power

The power consumption of SRAM varies widely depending on how frequently it is accessed; it can be as power-hungry as dynamic RAM, when used at high frequencies, and some ICs can consume many watts at full bandwidth. On the other hand, static RAM used at a somewhat slower pace, such as in applications with moderately clocked microprocessors, draws very little power and can have a nearly negligible power consumption when sitting idle

  1. REDIRECT Template:Spaced ndash in the region of a few micro-watts. Several techniques have been proposed to manage power consumption of SRAM-based memory structures.[2]

    Static RAM exists primarily as:

    • general purpose products
      • with asynchronous interface, such as the ubiquitous 28-pin 8K × 8 and 32K × 8 chips (often but not always named something along the lines of 6264 and 62C256 respectively), as well as similar products up to 16 Mbit per chip
      • with synchronous interface, usually used for caches and other applications requiring burst transfers, up to 18 Mbit (256K × 72) per chip
    • integrated on chip
      • as RAM or cache memory in micro-controllers (usually from around 32 bytes up to 128 kilobytes)
      • as the primary caches in powerful microprocessors, such as the x86 family, and many others (from 8 KB, up to many megabytes)
      • to store the registers and parts of the state-machines used in some microprocessors (see register file)
      • on application specific ICs, or ASICs (usually in the order of kilobytes)
      • in FPGAs and CPLDs

    Embedded use

    • Many categories of industrial and scientific subsystems, automotive electronics, and similar, contain static RAM.
    • Some amount (kilobytes or less) is also embedded in practically all modern appliances, toys, etc. that implement an electronic user interface.
    • Several megabytes may be used in complex products such as digital cameras, cell phones, synthesizers, etc.

    SRAM in its dual-ported form is sometimes used for realtime digital signal processing circuits.[citation needed]

    In computers

    SRAM is also used in personal computers, workstations, routers and peripheral equipment: CPU register files, internal CPU caches and external burst mode SRAM caches, hard disk buffers, router buffers, etc. LCD screens and printers also normally employ static RAM to hold the image displayed (or to be printed). Static RAM was used for the main memory of some early personal computers such as the TRS-80 Model 100 and Commodore VIC-20.


    Hobbyists, specifically homebuilt processor enthusiasts,[3] often prefer SRAM due to the ease of interfacing. It is much easier to work with than DRAM as there are no refresh cycles and the address and data buses are directly accessible rather than multiplexed. In addition to buses and power connections, SRAM usually requires only three controls: Chip Enable (CE), Write Enable (WE) and Output Enable (OE). In synchronous SRAM, Clock (CLK) is also included.[citation needed]

    Types of SRAM

    Non-volatile SRAM

    Non-volatile SRAMs, or nvSRAMs, have standard SRAM functionality, but they save the data when the power supply is lost, ensuring preservation of critical information. nvSRAMs are used in a wide range of situations—networking, aerospace, and medical, among many others[4] —where the preservation of data is critical and where batteries are impractical.

    By transistor type

    1. REDIRECT Template:Spaced ndash very fast but consumes a lot of power
      1. REDIRECT Template:Spaced ndash low power and very common today

        By function

        1. REDIRECT Template:Spaced ndash independent of clock frequency; data in and data out are controlled by address transition
          1. REDIRECT Template:Spaced ndash all timings are initiated by the clock edge(s). Address, data in and other control signals are associated with the clock signals

            In 1990s asynchronous SRAM memory used to be employed for fast access time. Asynchronous SRAM was used as main memory for small cache-less embedded processors used in everything from industrial electronics and measurement systems to hard disks and networking equipment, among many other applications. Nowadays, synchronous SRAM (e.g. DDR SRAM) is rather employed similarly like Synchronous DRAM - DDR SDRAM memory is rather used than asynchronous DRAM (Dynamic random-access memory). Synchronous memory interface is much faster as access time can be significantly reduced by employing pipeline architecture. Furthermore as DRAM is much cheaper than SRAM, SRAM is often replaced by DRAM, especially in the case when large volume of data is required. SRAM memory is however much faster for random (not block / burst) access. Therefore SRAM memory is mainly used for CPU cache, small on-chip memory, FIFOs or others buffers.

            By feature

            1. REDIRECT Template:Spaced ndash the turnaround is the number of clock cycles it takes to change access to the SRAM from write to read and vice versa. The turnaround for ZBT SRAMs or the latency between read and write cycle is zero.
              • syncBurst (syncBurst SRAM or synchronous-burst SRAM)
              1. REDIRECT Template:Spaced ndash features synchronous burst write access to the SRAM to increase write operation to the SRAM
                1. REDIRECT Template:Spaced ndash Synchronous, single read/write port, double data rate I/O
                  1. REDIRECT Template:Spaced ndash Synchronous, separate read and write ports, quadruple data rate I/O

                    By flip-flop type


                    File:SRAM Cell (6 Transistors).svg
                    A six-transistor CMOS SRAM cell.

                    A typical SRAM cell is made up of six MOSFETs. Each bit in an SRAM is stored on four transistors (M1, M2, M3, M4) that form two cross-coupled inverters. This storage cell has two stable states which are used to denote 0 and 1. Two additional access transistors serve to control the access to a storage cell during read and write operations. In addition to such six-transistor (6T) SRAM, other kinds of SRAM chips use 4, 8, 10 (4T, 8T, 10T SRAM), or more transistors per bit.[5][6][7] Four-transistor SRAM is quite common in stand-alone SRAM devices (as opposed to SRAM used for CPU caches), implemented in special processes with an extra layer of polysilicon, allowing for very high-resistance pull-up resistors. [8] The principal drawback of using 4T SRAM is increased static power due to the constant current flow through one of the pull-down transistors.

                    File:4T SRAM Cell.png
                    Four transistor SRAM provides advantages in density at the cost of manufacturing complexity. The resistors must have small dimensions and large values.

                    This is sometimes used to implement more than one (read and/or write) port, which may be useful in certain types of video memory and register files implemented with multi-ported SRAM circuitry.

                    Generally, the fewer transistors needed per cell, the smaller each cell can be. Since the cost of processing a silicon wafer is relatively fixed, using smaller cells and so packing more bits on one wafer reduces the cost per bit of memory.

                    Memory cells that use fewer than four transistors are possible

                    1. REDIRECT Template:Spaced ndash but, such 3T[9][10] or 1T cells are DRAM, not SRAM (even the so-called 1T-SRAM).

                      Access to the cell is enabled by the word line (WL in figure) which controls the two access transistors M5 and M6 which, in turn, control whether the cell should be connected to the bit lines: BL and BL. They are used to transfer data for both read and write operations. Although it is not strictly necessary to have two bit lines, both the signal and its inverse are typically provided in order to improve noise margins.

                      During read accesses, the bit lines are actively driven high and low by the inverters in the SRAM cell. This improves SRAM bandwidth compared to DRAMs

                      1. REDIRECT Template:Spaced ndash in a DRAM, the bit line is connected to storage capacitors and charge sharing causes the bitline to swing upwards or downwards. The symmetric structure of SRAMs also allows for differential signaling, which makes small voltage swings more easily detectable. Another difference with DRAM that contributes to making SRAM faster is that commercial chips accept all address bits at a time. By comparison, commodity DRAMs have the address multiplexed in two halves, i.e. higher bits followed by lower bits, over the same package pins in order to keep their size and cost down.

                        The size of an SRAM with m address lines and n data lines is 2m words, or 2m × n bits. The most common word size is 8 bits, meaning that a single byte can be read or written to each of 2m different words within the SRAM chip. Several common SRAM chips have 11 address lines (thus a capacity of 2m = 2,048 = 2k words) and an 8-bit word, so they are referred to as "2k × 8 SRAM".

                        SRAM operation

                        An SRAM cell has three different states. It can be in: standby (the circuit is idle), reading (the data has been requested) and writing (updating the contents). The SRAM to operate in read mode and write mode should have "readability" and "write stability" respectively. The three different states work as follows:

                        If the word line is not asserted, the access transistors M5 and M6 disconnect the cell from the bit lines. The two cross-coupled inverters formed by M1 – M4 will continue to reinforce each other as long as they are connected to the supply.
                        In theory, reading process requires only asserting the word line WL and reading the SRAM cell state by a single access transistor and bit line, e.g. M6, BL. Nevertheless bit lines are relatively long with large parasitic capacitance. Therefore to speed-up reading, more complex process is used in practice: The read cycle is started by precharging by an external module (not shown in the figures) both bit lines BL and BL, i.e. driving the bit lines to a threshold voltage (midrange voltage between logical 1 and 0). Then asserting the word line WL, enabling both the access transistors M5 and M6 which causes that the bit line BL voltage either slightly drops (bottom NMOS transistor M3 is ON and top PMOS transistor M4 is off) or rises (top PMOS transistor M4 is on). It should be noted that if BL voltage rises, the BL voltage drops, and vice versa. Then the BL and BL lines will have a small voltage difference between them while reaching a sense amplifier, which will sense which line has the higher voltage thus determining whether there was 1 stored or 0. The higher the sensitivity of the sense amplifier, the faster the speed of the read operation.
                        The start of a write cycle begins by applying the value to be written to the bit lines. If we wish to write a 0, we would apply a 0 to the bit lines, i.e. setting BL to 1 and BL to 0. This is similar to applying a reset pulse to an SR-latch, which causes the flip flop to change state. A 1 is written by inverting the values of the bit lines. WL is then asserted and the value that is to be stored is latched in. Note that the reason this works is that the bit line input-drivers are designed to be much stronger than the relatively weak transistors in the cell itself, so that they can easily override the previous state of the cross-coupled inverters. In practice, access NMOS transistors M5 and M6 have to be stronger than either bottom NMOS (M1, M3) or top PMOS (M2, M4) transistors. This is easily obtained as PMOS transistors are much weaker than NMOS when same sized. Consequently when one transistor pair (e.g. M3 and M4) is only slightly overriden by the write process, the opposite transistors pair (M1 and M2) gate voltage is also changed. This causes that M1 and M2 transistors can be easier overriden, and so on. Thus, cross-coupled inverters magnify the writing process.

                        Bus behavior

                        RAM with an access time of 70 ns will output valid data within 70 ns from the time that the address lines are valid. But the data will remain for a hold time as well (5–10 ns). Rise and fall times also influence valid timeslots with approximately 5 ns. By reading the lower part of an address range bits in sequence (page cycle) one can read with significantly shorter access time (30 ns).[11]

                        See also


                        1. ^ Sergei Skorobogatov (June 2002). "Low temperature data remanence in static RAM". University of Cambridge, Computer Laboratory. Retrieved 2008-02-27. 
                        2. ^ "A Survey of Architectural Techniques For Improving Cache Power Efficiency", S. Mittal, SUSCOM, 4(1), 33-43, 2014
                        3. ^ "Homemade CPU". 
                        4. ^ Computer organization. (4th ed. ed.). [S.l.]: McGraw-Hill. ISBN 0-07-114323-8. 
                        5. ^ A 160 mV Robust Schmitt Trigger Based Subthreshold SRAM
                        6. ^ United States Patent 6975532: Quasi-static random access memory
                        7. ^ [1]
                        8. ^ Preston, Ronald P. (2001). "14: Register Files and Caches" (PDF). The Design of High Performance Microprocessor Circuits. IEEE Press. p. 290. 
                        9. ^ United States Patent 6975531: 6F2 3-transistor DRAM gain cell
                        10. ^ 3T-iRAM(r) Technology
                        11. ^ "Tentative Toshiba mos digital integrated circuit silicon gate cmos 4,194,304-word by 16-bit cmos pseudo static RAM" (PDF).  070731